Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterFast, Reliable Chimney Cap & Crown Across Attleboro
A properly fitted chimney cap and intact crown in Attleboro typically runs $280-$850 depending on whether we’re capping a single flue or a shared multi-flue stack, and most jobs are completed in one visit. Our crews work the old jewelry-factory neighborhoods regularly, from the triple-deckers near downtown to the capes out by Route 1, and we carry the common cap sizes and crown repair materials on the truck so we’re not ordering parts. Call (508) 545-9737 - a live person answers, even at 11 PM on a Sunday.
We’ve been driving to Attleboro for over 42 years. Russell Haines started this company in 1984, and our dispatch runs out of the Boston office, but our technicians live in the corridor and know the local housing stock cold. That matters when your chimney is a hundred years old and shared with the unit next door.
Why Hearthstone Chimney Co. Is Attleboro’s Preferred Chimney Cap & Crown Company
Attleboro homeowners don’t call us because we’re the cheapest. They call because their neighbor did, or because they got tired of a cap that blew off in the first nor’easter. We’ve earned that reputation one stack at a time - documented with photos, explained in plain English, and backed by the 90-Day Done Right Promise in writing.
Our reviews from Attleboro customers mention the same things: the technician showed them camera footage of the cracked crown before quoting, the multi-flue cap actually fit all three liners, the bill matched the estimate. No arguing. We background-check and uniform every tech, and most cap and crown jobs in Attleboro finish in a single visit because we stock Gelco, Famco, and Copperfield caps in the common sizes for local flue dimensions.
Response time to Attleboro is typically next-day or within 48 hours during peak season. We know the tight streets near the old factories, the limited roof access on attached triple-deckers, and the permitting reality - there is no local Attleboro chimney permit for cap or crown work, but we document every job with before-and-after photos for your records and your insurance.
Our Chimney Cap & Crown Services in Attleboro
Cap Installation
New cap installation in Attleboro starts with measuring what you’ve actually got, not what a catalog says you should have. On the older two- and three-family homes near the jewelry-factory corridor, we often find flue liners that don’t match standard dimensions because of century-old coal-to-oil-to-gas conversions. We carry Gelco and Famco stainless caps in extended sizes, and we’ll fabricate a custom cap from Copperfield stock if your stack needs it. A single-flue cap installation in Attleboro typically runs $280-$420 installed.
Cap Replacement
Replacing a failed cap in Attleboro means diagnosing why it failed. Was it undersized for an oversized coal-era flue? Was it a single-flue cap forced onto a multi-flue stack, leaving the second or third liner exposed? We see both constantly. Our replacement process includes a Level-2 camera inspection of the flue beneath so you’re not throwing a new cap onto a liner that’s already compromised. Cap replacement in Attleboro generally falls between $320-$480.
Crown Repair
Crown repair is where Attleboro’s age and climate hit hardest. The original crown mortar on these 1880s-1920s brick stacks has endured a century of freeze-thaw cycles, and it’s usually spalled, cracked, or missing at the edges. We grind back to sound masonry, pour a new cementitious crown with proper slope and drip edge, and seal the interface with HeatShield where the crown meets the flue tile. Crown repair on a typical Attleboro stack runs $450-$750. Severe deterioration requiring full rebuild pushes toward the higher end.
Crown Coating
For crowns with surface cracking but intact structure, we apply a flexible crown coating formulated for New England’s thermal expansion. This isn’t paint - it’s a breathable, waterproof membrane that bridges hairline cracks and stops meltwater from penetrating the mortar. Crown coating in Attleboro costs $280-$450 and adds 10-15 years of protection if the underlying crown is basically sound. We camera-inspect first to confirm the crown isn’t hiding deeper damage.
Multi-Flue Cap
The multi-flue cap is our most-requested solution in Attleboro’s dense worker-housing neighborhoods. One stack, two or three units, and exhaust cross-contaminating between floors because a previous owner cheaped out with separate single-flue caps or left liners bare. We measure the full stack width, account for flue spacing and draft requirements, and install a custom multi-flue cap from Olympia Chimney or fabricate from Copperfield that covers every liner with independent draft clearance. Multi-flue caps in Attleboro run $480-$850 depending on stack width and access difficulty.
Custom Cap
When standard dimensions don’t fit - a common problem on Attleboro’s retrofitted coal-era chimneys - we build custom. Russell Haines reviews the measurements personally, and we fabricate in stainless or copper with proper mesh screening and a lid profile that sheds snow and leaves. Custom caps start around $650 and scale with material and complexity.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Attleboro
We don’t use builder-grade hardware. Our trucks stock professional-grade caps and crown materials from Gelco, Olympia Chimney, Famco, and Copperfield - the brands that other chimney companies in Attleboro often have to special-order. That means your cap or crown job doesn’t wait on a warehouse in Ohio. For crown repairs, we use HeatShield’s crown seal system and premium cementitious mixes rated for the freeze-thaw abuse of southeastern Massachusetts winters. When we quote a job, the parts are already on the route.
Common Chimney Cap & Crown Problems We See in Attleboro Homes
- Crown mortar spalled by a century of freeze-thaw. Attleboro’s inland location delivers hard winters, and the original crown on these jewelry-era brick stacks was never designed to survive 120 years of frost. Water gets in, freezes, pops the surface, and now your flue is taking meltwater every spring.
- Single-flue caps on multi-flue stacks. We see this on triple-deckers from Pleasant Street to the old Slater mill area - one cap covers one liner, but the second and third flues vent into open air, pulling exhaust sideways into neighboring units and letting squirrels nest two feet from your bedroom.
- Missing caps after wind events. The narrow streets downtown create wind tunneling between buildings, and poorly secured caps lift off. We anchor with stainless straps and masonry screws, not the friction-fit clips that fail first.
- Coal-era flues oversized for modern appliances. These flues draft poorly even with a good cap, and a bad cap makes it worse - cold air drops down, condensation accelerates creosote, and the whole system works against itself. We size caps for the actual flue, not the appliance.
Pricing for Chimney Cap & Crown in Attleboro, MA
| Service | Typical Range in Attleboro |
|---|---|
| Single-flue cap installation | $280 - $420 |
| Cap replacement (standard size) | $320 - $480 |
| Crown coating | $280 - $450 |
| Crown repair (partial rebuild) | $450 - $750 |
| Multi-flue cap (2-3 flues) | $480 - $850 |
| Custom fabricated cap | $650 - $1,100+ |
What moves you within these ranges? Stack height and roof access are the big ones - a triple-decker on a narrow lot with limited ladder staging takes longer than a ranch on a quarter-acre. The condition of the existing crown matters too; a cap can go on in an hour, but a crown that needs rebuilding adds time and material. We give you a firm number before we start, and that number doesn’t change. Estimates are free, and we bring the camera so you see what we see.
Attleboro’s housing density and age mean we do more multi-flue and crown-repair work here than in newer suburbs like Franklin or Bellingham. The pricing reflects that complexity - and the fact that doing it wrong on a shared stack creates liability between tenants that nobody wants.
We Also Serve Cities Near Attleboro
Our crews cover the full corridor - Chimney Cap & Crown in Attleboro is our home territory, but we run regularly to Plainville, Mansfield, Wrentham, and Norfolk for cap and crown work on similar vintage housing. Scheduling is coordinated from our Boston office, and we route to minimize your wait. If you’re in one of these towns and have a shared-stack situation, we’ve seen it.
Serving Attleboro, MA - Our Local Coverage Area
We’re based in the Attleboro area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Chimney Cap & Crown in Attleboro
Yes, and it should. A properly sized multi-flue cap covers every liner opening with independent draft clearance, stopping cross-contamination between units. We measure the full stack width and flue spacing, then source or fabricate a cap that fits. On a triple-decker near the old jewelry-factory corridor, our Chimney Cap & Crown tech found a crumbling chimney crown dropping mortar into one flue while a neighbor’s second flue in the same stack was pulling exhaust sideways into a third-floor unit. We rebuilt the crown with a HeatShield-sealed edge and set a custom multi-flue cap sized so each liner drafts independently, stopping the cross-draft and the spalling at the top course. Call (508) 545-9737 for a free estimate - we’ll camera-inspect all three flues and show you exactly what’s happening up there.
Your crown was poured a century ago with mortar mixes that weren’t formulated for freeze-thaw cycling, and it’s been through 120 southeastern Massachusetts winters. Newer homes use concrete crowns with expansion joints and proper slope - yours was built for coal exhaust and never upgraded. The brick faces spall, the mortar erodes, and water gets behind everything. We see this on virtually every pre-1940 stack in Attleboro’s core neighborhoods. Crown repair or coating stops the cycle if we catch it before the structural brick is compromised. Call (508) 545-9737 and we’ll show you the camera footage.
You’ll smell it, or you’ll see soot staining at the fireplace throat, or you’ll notice your carbon monoxide detector acting up when the downstairs tenant runs their boiler hard. On a shared stack, a missing cap on one flue creates negative pressure that pulls exhaust from the neighboring flue sideways. This is dangerous, not just inconvenient. We confirm it with a smoke test and camera inspection - documented with photos you can show your landlord or your own tenant. If you suspect cross-draft in an Attleboro multi-family, call (508) 545-9737 today; we’ll prioritize the inspection.
Yes. Your gas or oil appliance still produces acidic condensation that eats flue tile, and an uncapped flue is an open door for rain, squirrels, and downdrafts that blow out pilot lights. In Attleboro’s dense neighborhoods, a missing cap on your flue also exposes the stack to cross-draft from neighboring units. The cap costs less than one service call for a flooded boiler or a dead pilot in February. Call (508) 545-9737 for an exact quote - estimates are free.
We grind back all loose and spalled material to sound masonry, assess the flue tile interface for gaps where exhaust could leak into the chimney cavity, rebuild the crown with proper slope and overhang so water sheds away from the brick, and seal the flue-to-crown joint with HeatShield. On coal-era chimneys, we often find the flue tile is cracked or the clay liner is missing sections from decades of thermal shock - we’ll show you the camera evidence and tell you plainly whether the crown repair can stand alone or if the liner needs addressing too. No recommendation without photos you can see. Call (508) 545-9737 to schedule.
Written by Russell Haines, Owner at Hearthstone Chimney Co., serving Attleboro since 1984.